Azek Rail Manuel d'utilisateur télécharger pdf

AZEK Rail

Install Guide

TRIM MOULDING DECK PORCH RAIL PAVERS

Installing AZEK Rail with CableRail by Feeney® .......................................................................... 1

Installing CableRail by Feeney® for AZEK Rail ........................................................................... 7

Installing AZEK Rail Stairs with CableRail by Feeney® ............................................................10

Installing CableRail by Feeney® Stairs for AZEK Rail ............................................................... 14

Notes ....................................................................................................................................................18

• Please read all instructions completely before starting any part of the installation.

• AZEK Rail should be installed using the same good building principles used to install wood or composite

railing and in accordance with the local building codes and the installation guidelines included below.

AZEK Building Products Inc. accepts no liability or responsibility for the improper installation of this product.

• AZEK Rail may not be suitable for every application and it is the sole responsibility of the installer to be sure

that AZEK Rail is t for the intended use. Since all installations are unique, it is also the installer’s

responsibility to determine specic requirements in regards to each Rail application.

• AZEK Building Products Inc. recommends that all applications be reviewed by a licensed architect, engineer

or local building ofcial before installation. If you have any questions or need further assistance, please call

AZEK Customer Service at 877-ASK-AZEK (877-275-2935) or visit our website at www.azek.com.

• AZEK Railing is tested as a whole system and should be used that way. It is not intended to be used in

conjunction with other railing systems or fasteners.

• The following Installation Guidelines are applicable for installation of AZEK Premier, AZEK Trademark, and

AZEK Reserve Rail Systems (except AZEK Reserve over post applications).

• IMPORTANT: Make sure the DRIVE TOOL/DRILL is congured or set to use the SCREW setting when driving

and/or tightening all FASTENERS.

• SAFETY: Always wear goggles when handling, cutting, drilling and fastening materials.

• Failure to install this product in accordance with applicable building codes and AZEK’s written Rail Install

Guide may lead to personal injury, affect rail system performance and void the product warranty.

1 2 3 4 5 6 ... 19 20

Résumé du contenu

Page 1 - Install Guide

AZEK RailInstall GuideTRIM MOULDING DECK PORCH RAIL PAVERSInstalling AZEK Rail with CableRail by Feeney® ...

Page 2 - 10’, 8’ and 6’ lengths

Page 10Installing AZEK Rail Stairs with CableRail by Feeney®MEASURE SUPPORT RAILSSupport Rails are rotated 90° for stair rail applications.312Top Rail

Page 3 - SUPPORT BLOCK

Page 11Installing AZEK Rail Stairs with CableRail by Feeney®Pre-drill 7/64”#8 x 3/4” Coated ScrewsCenter screw aligned with rail centerlinePre-drill

Page 4

Page 12Installing AZEK Rail Stairs with CableRail by Feeney®#10 x 2” Coated ScrewsBottom RailPre-drill 3/16” Use Intermediate Base Plate as templateAT

Page 5 - ATTACH INTERMEDIATE BALUSTERS

Page 13Installing AZEK Rail Stairs with CableRail by Feeney®Lower the rails perpendicular to the deck surface.TRANSFER HOLE LOCATION ON POST SLEEVE•

Page 6 - ATTACH TOP SUPPORT RAIL

Page 14Installing AZEK Rail Stairs with CableRail by Feeney®Use a scrap piece of baluster trimmed at the stair angle as a guide.Anchor posts should no

Page 7

Page 15Installing CableRail by Feeney® Stairs for AZEK RailLeave about 1” of machine thread exposed for cable take-up.PRE-DRILL THROUGH POST SLEEVES•

Page 8 - CUT CABLE TO LENGTH

Page 16Installing CableRail by Feeney® Stairs for AZEK RailTHREAD CABLE65• When all of the hardware is in place, insert one end of the Cable into the

Page 9 - Tightening Order

Page 17Installing CableRail by Feeney® Stairs for AZEK RailIf necessary, the Cable can be removed from the Quick-Connect ﬁ tting by using the Quick-Co

Page 10 - TRIM RAILS

Page 18Notes

Page 11 - INSTALL BOTTOM SUPPORT RAIL

Page 19Notes

Page 12 - PRE-DRILL BOTTOM RAIL

Page 2Installing AZEK Rail with CableRail by Feeney®Quick-Connect Fitting5.5”5 1/2” x 5 1/2” Post Sleeve5.5” Hardware Mounting Kit 4 - Mounting Bracke

Page 13

Page 14 - Stairs for AZEK Rail

Page 3Installing AZEK Rail with CableRail by Feeney®40” above deck surface is optimal for 36” railing heights.If you do not have a the template, posit

Page 15

Page 4CUT AND PREP BOTTOM RAIL AND TOP SUPPORT RAILINSTALL BOTTOM SUPPORT RAIL• Position rail assembly onto Support Blocks.546’ sections require 1 Int

Page 16

Page 5Installing AZEK Rail with CableRail by Feeney®INSTALL BOTTOM RAILATTACH INTERMEDIATE BALUSTERS76Bottom RailIntermediate BalusterPre-drill3/16”#1

Page 17

Page 6Installing AZEK Rail with CableRail by Feeney®TRANSFER HOLE LOCATION ONTO POST SLEEVE• Use an extra Intermediate Baluster, rested on the Bottom

Page 18

Page 7Installing CableRail by Feeney® for AZEK Rail1” Anchor posts should not exceed 60 feet apart during any continuous run of cable.Optional - Prote

Page 19

Page 8Installing CableRail by Feeney® for AZEK RailATTACH QUICK-CONNECT AND QUICK-CONNECT SWIVEL FITTINGS• Screw on Quick-Connect ﬁ ttings snuggly ag

Page 20 - AZEK Building Products, Inc

Page 9Installing CableRail by Feeney® for AZEK RailATTACH QUICK-CONNECT AND QUICK-CONNECT CABLE FITTINGS6• Use a set of 3/8” open-ended wrenches to t