AZEK RailInstall GuideTRIM MOULDING DECK PORCH RAIL PAVERSInstalling AZEK Rail with Balusters ...
Page 10Installing AZEK Rail Stairs with BalustersPre-drill7/64”#8 x 2 5/8” Coated ScrewsINSTALL BOTTOM SUPPORT RAIL• Position Top Rail over Support Ra
Page 11Installing AZEK Rail with CableRail by Feeney®Quick-Connect Fitting5.5”5 1/2” x 5 1/2” Post Sleeve5.5” Hardware Mounting Kit 4 - Mounting Brack
Page 12Installing AZEK Rail with CableRail by Feeney®40” above deck surface is optimal for 36” railing heights.If you do not have a the template, posi
Page 13CUT AND PREP BOTTOM RAIL AND TOP SUPPORT RAILINSTALL BOTTOM SUPPORT RAIL• Position rail assembly onto Support Blocks.546’ sections require 1 In
Page 14Installing AZEK Rail with CableRail by Feeney®INSTALL BOTTOM RAILATTACH INTERMEDIATE BALUSTERS76Bottom RailIntermediate BalusterPre-drill3/16”#
Page 15Installing AZEK Rail with CableRail by Feeney®TRANSFER HOLE LOCATION ONTO POST SLEEVE• Use an extra Intermediate Baluster, rested on the Botto
Page 16Installing CableRail by Feeney® for AZEK Rail1” Anchor posts should not exceed 60 feet apart during any continuous run of cable.Optional - Prot
Page 17Installing CableRail by Feeney® for AZEK RailATTACH QUICK-CONNECT AND QUICK-CONNECT SWIVEL FITTINGS• Screw on Quick-Connect ttings snuggly ag
Page 18Installing CableRail by Feeney® for AZEK RailATTACH QUICK-CONNECT AND QUICK-CONNECT CABLE FITTINGS6• Use a set of 3/8” open-ended wrenches to
Page 19Installing AZEK Rail Stairs with CableRail by Feeney®ATTACH QUICK-CONNECT AND QUICK-CONNECT CABLE FITTINGSMEASURE SUPPORT RAILSSupport Rails ar
Page 24 - Mounting Brackets2 - Support Blocks16 - #8 x 3/4” Screws 6 - #8 x 1 3/4” Screws 6 - #8 x 2 5/8” Screws (Stairs Only) 6 - #8 x 3” Screws 12 -
Page 20Installing AZEK Rail Stairs with CableRail by Feeney®Pre-drill 7/64”#8 x 3/4” Coated ScrewsCenter screw aligned with rail centerline4PREP BOTT
Page 21Installing AZEK Rail Stairs with CableRail by Feeney®#10 x 2” Coated ScrewsBottom RailPre-drill 3/16” Use Intermediate Base Plate as templateAT
Page 22Installing AZEK Rail Stairs with CableRail by Feeney®Lower the rails perpendicular to the deck surface.TRANSFER HOLE LOCATION ON POST SLEEVE•
Page 23Installing AZEK Rail Stairs with CableRail by Feeney®Use a scrap piece of baluster trimmed at the stair angle as a guide.Anchor posts should no
Page 24Installing CableRail by Feeney® Stairs for AZEK RailLeave about 1” of machine thread exposed for cable take-up.PRE-DRILL THROUGH POST SLEEVES•
Page 25Installing CableRail by Feeney® Stairs for AZEK RailTHREAD CABLE65• When all of the hardware is in place, insert one end of the Cable into the
Page 26Installing CableRail by Feeney® Stairs for AZEK RailIf necessary, the Cable can be removed from the Quick-Connect tting by using the Quick-Con
Page 27Installing AZEK Rail with Glass Inll2.73”2.05”Trademark Bottom Rail3.5”2.64”Trademark Top Rail5.38”2.72”Reserve Top Rail3.5”2.05”Reserve Botto
Page 28Installing AZEK Rail with Glass InllDIMENSIONAL CONSTRAINTS FOR STRAIGHT SECTIONDIMENSIONAL CONSTRAINTS FOR STAIR SECTIONMax of 63”Min 27.75 f
Page 29Installing AZEK Rail with Glass Inll39” above deck surface is optimal for 36” railing heights.If you do not have a the template, position the
Page 3If you do not have the template, position the top of the Support Block 4” above the deck. INSTALL LOWER SUPPORT BLOCK• Position template at bo
Page 30Installing AZEK Rail with Glass InllTRIM RAILS, EXTRUSIONS, AND GASKETSINSTALL BOTTOM SUPPORT RAIL54• Measure distance between the posts at t
Page 31Installing AZEK Rail with Glass InllATTACH LOWER GASKET AND INSTALL GLASS PANELASSEMBLE LOWER RAIL SECTION76• Apply Rubber Gasket to bottom o
Page 32INSTALL TOP SUPPORT RAILINSTALL TOP GASKET AND TOP GLASS CHANNEL98• Align top Support Rail to center of Posts.• Attach Brackets to Top Suppor
Page 33INSTALL TOP RAIL AND POST CAPS10• Attach Post Caps using exterior grade caulk applied to the underside of the Cap.#8 x 2 1/4” Coated Screws3/1
Page 34Installing AZEK Rail Stairs with Glass InllConsult your local building codes for guard and handrail requirements. • Trim Post Sleeve to desir
Page 35Glass Channels must be at least 4” shorter than rail.Installing AZEK Rail Stairs with Glass Inll• Using lengths in Step 3 as a reference, mea
Page 36Installing AZEK Rail Stairs with Glass InllASSEMBLE LOWER RAIL SECTION6• Place Bottom Rail over Bottom Support Rail.• Install Bottom Glass C
Page 37Installing AZEK Rail Stairs with Glass InllINSTALL TOP GASKET AND TOP GLASS CHANNEL8Top Glass Channel: Pre-drilled holes are on side• Place R
Page 38Installing AZEK Rail Stairs with Glass InllINSTALL TOP RAIL AND POST CAPS• Attach Post caps using exterior grade caulk applied to the undersid
Page 39Notes
Page 4Installing AZEK Rail with Balusters7/64” Pre-drill#8 x 3” Green Coated ScrewsOdd number of balustersEven number of balustersSPACE BALUSTER AND T
AZEK Building Products, Inc.888 North Keyser Avenue • Scranton, PA 18504www.AZEK.com • (877) ASK-AZEK (877) 275-2935© 2013 AZEK ARAILINSTALL | 0
Page 5Installing AZEK Rail with BalustersINSTALL RAIL ASSEMBLYASSEMBLE BALUSTER SECTION• Align Top Support Rail to center of Posts.• Attach Mounting B
Page 6INSTALL TOP RAIL AND POST CAPS• Measure and cut Top Rail to length. Trim both ends for a clean cut. • Attach Post caps using exterior grade caul
Page 7Installing AZEK Rail Stairs with BalustersTrim RailsTRIM RAILS• Transfer measurement from Bottom Support Rail to Bottom Rail.• Trim Top Rail t
Page 8Installing AZEK Rail Stairs with BalustersASSEMBLE BALUSTERS• Attach Balusters to Top and Bottom Support Rails and attach Brackets to Top Suppo
Page 9Installing AZEK Rail Stairs with Balusters• Rotate Rail assembly out of way to fasten Support Block.Pre-drill 7/64”#8 x 3/4” Coated ScrewsCente
Commentaires sur ces manuels